# DC motor Hall sensor/ switch

**URL:** <https://forum.digikey.com/t/dc-motor-hall-sensor-switch/57072>\
**Category:** Sensors Transducers\
**Tags:** magnetic-sensors, honeywell-sensing-and-productivity-solutions, cross-reference\
**Created:** [July 5, 2025, 12:43am UTC](https://forum.digikey.com/t/dc-motor-hall-sensor-switch/57072 "2025-07-05T00:43:02Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![kcona3](https://avatars.discourse-cdn.com/v4/letter/k/c6cbf5/32.png) [@kcona3](https://forum.digikey.com/u/kcona3)\
**Post date:** [July 5, 2025, 12:43am UTC](https://forum.digikey.com/t/dc-motor-hall-sensor-switch/57072/1 "2025-07-05T00:43:02Z")

</div>

Having problem getting the correct hall sensor/ switch for DC hub motor on a scooter.  
I ordered some last week but the output voltage was not high enough.  
It was only 2.5V  
The control voltage is 5 volts. And I need an output voltage of 5volts.  
The number on the original sensor is S41327. This sensor is no longer available.

---

<div class="post-metadata">

**Author:** ![Nathan\_Henneman](https://avatars.discourse-cdn.com/v4/letter/n/838e76/32.png) [@Nathan\_Henneman](https://forum.digikey.com/u/Nathan_Henneman)\
**Post date:** [July 5, 2025, 12:59am UTC](https://forum.digikey.com/t/dc-motor-hall-sensor-switch/57072/2 "2025-07-05T00:59:26Z")

</div>

> [@kcona3](#):
>
> S41327

Hello Kcona3, thank you for contacting DigiKey Technical Support.  
[These are all the 5volt options we carry.](https://www.digikey.com/en/products/filter/switches-solid-state/565?s=N4IgjCBcoEwOwDYqgMZQGYEMA2BnApgDQgD2UA2iAKxwAcMADCMVQgJxhLEJgDMvAFmYgevKjGFh4DOHEnwwneXCkRiU2rN7zNiHXDZN1vBjFpHwJk3OMwYYC3zv3JvZ0Nt2qru-x8wBNn84CWMBXVdw2g9LKJtY2logsLYYbRSBeL5AsFpItnN8zVcEeGSQRng4C0qDR15S8WFathiWvOJK83SK03NvTr6ZZr7BEbMGDt6zXniuuB6wBcUsuAFc8qX12gHwRCom9X2qGKWEA64985phATuBBBjAg4ZHA3gppdS1yXeEKbsmlmzTMa1CFVBmRBmkC0LgBxGtHONUmjzaqNKiPY5Xskz8nQctAaIAAusQAA4AFygIAAypSAE4ASwAdgBzEAAXxY1WQIDQkCweCIpAoIDEATYSDJICpNPpzPZXPUBSC0H5GBwBGIZEglCYJO5IAAtBJ1QLGQBXEW6yjeQ1Gs2UAAWOGwAAJ8Oh0PgUJT3QQWbgSAzSZygA)  
The output is rated in amps not voltage.

---

<div class="post-metadata">

**Author:** ![kcona3](https://avatars.discourse-cdn.com/v4/letter/k/c6cbf5/32.png) [@kcona3](https://forum.digikey.com/u/kcona3)\
**Post date:** [July 6, 2025, 2:26am UTC](https://forum.digikey.com/t/dc-motor-hall-sensor-switch/57072/3 "2025-07-06T02:26:05Z")

</div>

Any idea which one would copy the characteristics of the the one I have.  
This is the number on the original hall sensor.  
Part #S41327

The supply voltage is 5v  
And the return voltage needs to be as close to that as possible.  
The ones I purchased last week only put out 2.5v and the controller does not see it. The voltage is too low.

---

<div class="post-metadata">

**Author:** ![bidrohini](https://avatars.discourse-cdn.com/v4/letter/b/ecae2f/32.png) [@bidrohini](https://forum.digikey.com/u/bidrohini)\
**Post date:** [July 7, 2025, 3:11pm UTC](https://forum.digikey.com/t/dc-motor-hall-sensor-switch/57072/4 "2025-07-07T15:11:30Z")

</div>

> [@kcona3](#):
>
> Having problem getting the correct hall sensor/ switch for DC hub motor on a scooter.  
> I ordered some last week but the output voltage was not high enough.  
> It was only 2.5V  
> The control voltage is 5 volts. And I need an output voltage of 5volts.  
> The number on the original sensor is S41327. This sensor is no longer available.

If you are looking for a replacement, you can check Honeywell SS41.