# Polarity Reversal using a DPDT Switch

**URL:** <https://forum.digikey.com/t/polarity-reversal-using-a-dpdt-switch/626>\
**Category:** Switches\
**Tags:** switches, electromechanical, tech-tips\
**Created:** [October 13, 2017, 9:39pm UTC](https://forum.digikey.com/t/polarity-reversal-using-a-dpdt-switch/626 "2017-10-13T21:39:12Z")\
**Posts on this page:** 5\
**Page:** 1

<div class="post-metadata">

**Author:** ![Robert\_Fay](https://sea2.discourse-cdn.com/digikey/user_avatar/forum.digikey.com/robert_fay/32/6529_2.png) [@Robert\_Fay](https://forum.digikey.com/u/Robert_Fay)\
**Post date:** [October 13, 2017, 9:39pm UTC](https://forum.digikey.com/t/polarity-reversal-using-a-dpdt-switch/626/1 "2017-10-13T21:39:12Z")

</div>

Below is a simple schematic that was created to help show a possible way to use a DPDT switch to reverse the polarity on a motor. You can see when the switch is is the up position the positive (+) from the voltage source is routed to the positive (+) side of the motor. When in the down position the positive side(+) is routed to the negative (-) side of the motor.

 ![DC Motor Reversing Switch 3](https://global.discourse-cdn.com/digikey/original/1X/dbf874b270a57f8da92d084faee28a8c8ddfa814.png)

Please note that this drawing is for informational purposes only. the full circuit would likely involve a form of protection and an off position in the switch. You also need to verify you have a bi directional motor. The Positive and negative on this motor are given for reference only.

---

<div class="post-metadata">

**Author:** ![Ryan\_2724](https://sea2.discourse-cdn.com/digikey/user_avatar/forum.digikey.com/ryan_2724/32/1716_2.png) [@Ryan\_2724](https://forum.digikey.com/u/Ryan_2724)\
**Post date:** [January 17, 2019, 9:11pm UTC](https://forum.digikey.com/t/polarity-reversal-using-a-dpdt-switch/626/2 "2019-01-17T21:11:45Z")

</div>

[Click here for DPDT switches: EG2458-ND | EG2419-ND](https://www.digikey.com/en/products/filter/toggle-switches/201?s=N4IgTCBcDaIKIHEwBYCsAOAtAOQCIAIAffRFARgE4dcQBdAGhFSlAAcozHX3IyAGPgF9BQA)

These are just a couple examples of motor reverse switches where the middle actuator position is “off”. EG2419-ND is (momentary) in each direction where EG2458-ND is latched on in each direction. Being that these have a center “off” position, these wouldn’t necessarily require a separate switch.

Since the above link was so popular, [click here for all of our DPDT switches with three actuator positions. Notice momentary and latching options with different termination styles.](https://www.digikey.com/en/products/filter/toggle-switches/201?s=N4IgjCBcpgzADFUBjKAzAhgGwM4FMAaEAeygG0RYAWeKgNipAF0iAHAFyhAGV2AnAJYA7AOYgAvkQBMsAKxIQqSJlyES5SgHY6ATjryisABxT4snczadIPfsLGSQAWikKl-AK5rSkCvJYgHFwS4uJAA)

---

<div class="post-metadata">

**Author:** ![Kristof\_2649](https://sea2.discourse-cdn.com/digikey/user_avatar/forum.digikey.com/kristof_2649/32/2325_2.png) [@Kristof\_2649](https://forum.digikey.com/u/Kristof_2649)\
**Post date:** [October 26, 2020, 5:45pm UTC](https://forum.digikey.com/t/polarity-reversal-using-a-dpdt-switch/626/3 "2020-10-26T17:45:26Z")

</div>

It may help for visualization to show the back of a DPDT switch for wiring, it’s a criss cross pattern:

![image](https://global.discourse-cdn.com/digikey/original/2X/1/1ef7b4776f210b019bed9d9f5899304345d1d08e.png)

---

<div class="post-metadata">

**Author:** ![sshannon74074](https://avatars.discourse-cdn.com/v4/letter/s/b77776/32.png) [@sshannon74074](https://forum.digikey.com/u/sshannon74074)\
**Post date:** [January 30, 2021, 4:37pm UTC](https://forum.digikey.com/t/polarity-reversal-using-a-dpdt-switch/626/4 "2021-01-30T16:37:51Z")

</div>

I need some help. I think I’m in the right area but have a slightly different application. I recently purchased a dpdt relay to reverse polarity on a linear actuator. here is the catch. I’m using a 6 volt (non-reversable) momentary 1 second signal to latch the 12 volt which needs to have reverse polarity to run the linear actuator up and down. Any help much appreciated

---

<div class="post-metadata">

**Author:** ![David\_1768](https://sea2.discourse-cdn.com/digikey/user_avatar/forum.digikey.com/david_1768/32/9762_2.png) [@David\_1768](https://forum.digikey.com/u/David_1768)\
**Post date:** [February 1, 2021, 12:26pm UTC](https://forum.digikey.com/t/polarity-reversal-using-a-dpdt-switch/626/5 "2021-02-01T12:26:21Z")

</div>

sshannon,

Like they explained above, you have to run jumpers in a criss-cross pattern.  
 ![Reversing Polarity](https://global.discourse-cdn.com/digikey/original/2X/2/29d728931bc82f9a414493e2e7c9c07dbea32986.jpeg)  
In the Normally Closed position, when the relay is not activated, the + will go out on the Blue line, and the - will be on the Red.  
When you active your relay, the + will be on the Red line, and the - on the blue.
