U-Boot SPL 2019.04 (May 05 2020 - 23:45:56 -0500) Trying to boot from MMC2 Loading Environment from EXT4... OK U-Boot 2019.04 (May 05 2020 - 23:45:56 -0500) GOOD CPU : AM335X-GP rev 2.1 I2C: ready DRAM: 512 MiB No match for driver 'omap_hsmmc' No match for driver 'omap_hsmmc' Some drivers were not found Reset Source: Power-on reset has occurred. RTC 32KCLK Source: External. MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from EXT4... OK Board: BeagleBone Black BeagleBone Black: BeagleBone: cape eeprom: i2c_probe: 0x54: BeagleBone: cape eeprom: i2c_probe: 0x55: BeagleBone: cape eeprom: i2c_probe: 0x56: BeagleBone: cape eeprom: i2c_probe: 0x57: Net: eth0: MII MODE Could not get PHY for cpsw: addr 0 cpsw, usb_ether Press SPACE to abort autoboot in 0 seconds board_name=[A335BNLT] ... switch to partitions #0, OK mmc0 is current device SD/MMC found on device 0 switch to partitions #0, OK mmc0 is current device Scanning mmc 0:1... gpio: pin 56 (gpio 56) value is 0 gpio: pin 55 (gpio 55) value is 0 gpio: pin 54 (gpio 54) value is 0 gpio: pin 53 (gpio 53) value is 1 switch to partitions #0, OK mmc0 is current device gpio: pin 54 (gpio 54) value is 1 Checking for: /uEnv.txt ... Checking for: /boot.scr ... Checking for: /boot/boot.scr ... Checking for: /boot/uEnv.txt ... gpio: pin 55 (gpio 55) value is 1 923 bytes read in 31 ms (28.3 KiB/s) Loaded environment from /boot/uEnv.txt debug: [dtb=am335x-zcpu.dtb] ... Using: dtb=am335x-zcpu.dtb ... Checking if uname_r is set in /boot/uEnv.txt... gpio: pin 56 (gpio 56) value is 1 Running uname_boot ... loading /boot/vmlinuz-4.19.106-bone-rt-r49 ... 8004096 bytes read in 540 ms (14.1 MiB/s) debug: [enable_uboot_overlays=] ... loading /boot/dtbs/4.19.106-bone-rt-r49/am335x-zcpu.dtb ... 58648 bytes read in 209 ms (273.4 KiB/s) uboot_overlays: add [enable_uboot_overlays=1] to /boot/uEnv.txt to enable... debug: [console=ttyO0,115200n8 root=/dev/mmcblk0p1 ro rootfstype=ext4 rootwait loglevel=7 coherent_pool=1M net.ifnames=0] ... debug: [bootz 0x82000000 - 0x88000000] ... ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Loading Device Tree to 8ffee000, end 8ffff517 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.106-bone49 (jak@ws271) (gcc version 8.3.0 (GNU Toolchain for the A-profile Architecture 8.3-2019.0 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=50c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] Memory policy: Data cache writeback [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 48 MiB at 0x9d000000 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] random: get_random_bytes called from start_kernel+0x83/0x400 with crng_init=0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129920 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/mmcblk0p1 ro rootfstype=ext4 rootwait loglevel=7 coherent_pool0 [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 455152K/524288K available (8192K kernel code, 1002K rwdata, 2972K rodata, 1024K init, 315K bss, 19984K reser) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf800000 - 0xbfe00000 ( 6 MB) [ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (9184 kB) [ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (1024 kB) [ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1003 kB) [ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 316 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] ftrace: allocating 37707 entries in 74 pages [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] Tasks RCU enabled. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts [ 0.000000] ti_dt_clocks_register: missing clkctrl nodes, please update your dts. [ 0.000000] OMAP clockevent source: timer2 at 24000000 Hz [ 0.000011] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000030] clocksource: timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000042] OMAP clocksource: timer1 at 24000000 Hz [ 0.000431] timer_probe: no matching timers found [ 0.000608] Console: colour dummy device 80x30 [ 0.000633] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' [ 0.000640] This ensures that you still see kernel messages. Please [ 0.000646] update your kernel commandline. [ 0.000690] Calibrating delay loop... 995.32 BogoMIPS (lpj=1990656) [ 0.047189] pid_max: default: 32768 minimum: 301 [ 0.047452] Security Framework initialized [ 0.047468] Yama: becoming mindful. [ 0.047585] AppArmor: AppArmor initialized [ 0.047669] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.047682] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.048548] CPU: Testing write buffer coherency: ok [ 0.048603] CPU0: Spectre v2: using BPIALL workaround [ 0.049436] Setting up static identity map for 0x80100000 - 0x80100054 [ 0.049582] rcu: Hierarchical SRCU implementation. [ 0.052481] EFI services will not be available. [ 0.053923] devtmpfs: initialized [ 0.063870] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 0.064288] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.064310] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.068007] xor: measuring software checksum speed [ 0.107220] arm4regs : 1222.000 MB/sec [ 0.147192] 8regs : 1095.000 MB/sec [ 0.187190] 32regs : 1055.000 MB/sec [ 0.227190] neon : 1699.000 MB/sec [ 0.227199] xor: using function: neon (1699.000 MB/sec) [ 0.227214] pinctrl core: initialized pinctrl subsystem [ 0.227931] DMI not present or invalid. [ 0.228316] NET: Registered protocol family 16 [ 0.231786] DMA: preallocated 1024 KiB pool for atomic coherent allocations [ 0.232440] omap_hwmod: emif: no dt node [ 0.232450] ------------[ cut here ]------------ [ 0.232483] WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2368 _init.constprop.19+0x157/0x428 [ 0.232490] omap_hwmod: emif: doesn't have mpu register target base [ 0.232497] Modules linked in: [ 0.232516] CPU: 0 PID: 1 Comm: swapper Not tainted 4.19.106-bone49 #1 [ 0.232522] Hardware name: Generic AM33XX (Flattened Device Tree) [ 0.232561] [] (unwind_backtrace) from [] (show_stack+0x11/0x14) [ 0.232577] [] (show_stack) from [] (__warn.part.3+0x83/0x94) [ 0.232590] [] (__warn.part.3) from [] (warn_slowpath_fmt+0x51/0x66) [ 0.232604] [] (warn_slowpath_fmt) from [] (_init.constprop.19+0x157/0x428) [ 0.232619] [] (_init.constprop.19) from [] (__omap_hwmod_setup_all+0x33/0xc0) [ 0.232635] [] (__omap_hwmod_setup_all) from [] (do_one_initcall+0x37/0x17c) [ 0.232658] [] (do_one_initcall) from [] (kernel_init_freeable+0x1b1/0x224) [ 0.232679] [] (kernel_init_freeable) from [] (kernel_init+0xd/0xd6) [ 0.232694] [] (kernel_init) from [] (ret_from_fork+0x11/0x38) [ 0.232703] Exception stack(0xdc0fdfb0 to 0xdc0fdff8) [ 0.232713] dfa0: 00000000 00000000 00000000 00000000 [ 0.232724] dfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 0.232735] dfe0: 00000000 00000000 00000000 00000000 00000013 00000000 [ 0.232751] ---[ end trace 55f71c9b1c852df8 ]--- [ 0.248909] omap_hwmod: debugss: _wait_target_disable failed [ 0.288637] audit: initializing netlink subsys (disabled) [ 0.289554] cpuidle: using governor menu [ 0.293630] audit: type=2000 audit(0.288:1): state=initialized audit_enabled=0 res=1 [ 0.293806] OMAP GPIO hardware version 0.1 [ 0.302829] No ATAGs? [ 0.302838] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.311942] raid6: using algorithm neonx8 gen() 0 MB/s [ 0.311959] raid6: .... xor() 0 MB/s, rmw enabled [ 0.311967] raid6: using neon recovery algorithm [ 0.317183] edma 49000000.edma: TI EDMA DMA engine driver [ 0.319295] SCSI subsystem initialized [ 0.319580] usbcore: registered new interface driver usbfs [ 0.319626] usbcore: registered new interface driver hub [ 0.319739] usbcore: registered new device driver usb [ 0.321248] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz [ 0.321539] pps_core: LinuxPPS API ver. 1 registered [ 0.321549] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.321570] PTP clock support registered [ 0.322016] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400 [ 0.322969] NetLabel: Initializing [ 0.322982] NetLabel: domain hash size = 128 [ 0.322989] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.323077] NetLabel: unlabeled traffic allowed by default [ 0.323591] clocksource: Switched to clocksource timer1 [ 0.440755] VFS: Disk quotas dquot_6.6.0 [ 0.440844] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.441434] AppArmor: AppArmor Filesystem Enabled [ 0.450267] NET: Registered protocol family 2 [ 0.451058] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes) [ 0.451088] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.451128] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 0.451166] TCP: Hash tables configured (established 4096 bind 4096) [ 0.451273] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.451291] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.451478] NET: Registered protocol family 1 [ 0.452251] RPC: Registered named UNIX socket transport module. [ 0.452265] RPC: Registered udp transport module. [ 0.452271] RPC: Registered tcp transport module. [ 0.452278] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.453177] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available [ 0.456135] Initialise system trusted keyrings [ 0.456409] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 0.461886] zbud: loaded [ 0.464400] NFS: Registering the id_resolver key type [ 0.464439] Key type id_resolver registered [ 0.464447] Key type id_legacy registered [ 0.464464] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.464730] fuse init (API version 7.27) [ 0.471488] Key type asymmetric registered [ 0.471506] Asymmetric key parser 'x509' registered [ 0.471579] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 0.471881] io scheduler noop registered [ 0.471893] io scheduler deadline registered [ 0.472211] io scheduler cfq registered (default) [ 0.472222] io scheduler mq-deadline registered [ 0.473500] pinctrl-single 44e10800.pinmux: 142 pins, size 568 [ 0.474370] gpio-of-helper ocp:cape-universal: ready [ 0.476725] wkup_m3_ipc 44e11324.wkup_m3_ipc: could not get rproc handle [ 0.477658] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled [ 0.480207] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 30, base_baud = 3000000) is a 8250 [ 1.350563] random: fast init done [ 1.375877] console [ttyS0] enabled [ 1.380246] 48022000.serial: ttyS1 at MMIO 0x48022000 (irq = 31, base_baud = 3000000) is a 8250 [ 1.389775] 48024000.serial: ttyS2 at MMIO 0x48024000 (irq = 32, base_baud = 3000000) is a 8250 [ 1.399289] 481a8000.serial: ttyS4 at MMIO 0x481a8000 (irq = 33, base_baud = 3000000) is a 8250 [ 1.409865] omap_rng 48310000.rng: Random Number Generator ver. 20 [ 1.416377] random: crng init done [ 1.536412] libphy: Fixed MDIO Bus: probed [ 1.591668] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 [ 1.599395] davinci_mdio 4a101000.mdio: no live phy, scanning all [ 1.612478] libphy: 4a101000.mdio: probed [ 1.617162] cpsw 4a100000.ethernet: Detected MACID = f4:5e:ab:32:87:04 [ 1.623858] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 [ 1.630263] cpsw 4a100000.ethernet: ALE Table size 1024 [ 1.635563] cpsw 4a100000.ethernet: cpts: overflow check period 1250 (jiffies) [ 1.643674] cpsw 4a100000.ethernet: cpsw: Detected MACID = f4:5e:ab:32:87:06 [ 1.651859] usbcore: registered new interface driver smsc95xx [ 1.657948] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.664573] ehci-omap: OMAP-EHCI Host Controller driver [ 1.669944] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.676249] usbcore: registered new interface driver usb-storage [ 1.684106] am335x-phy-driver 47401300.usb-phy: 47401300.usb-phy supply vcc not found, using dummy regulator [ 1.694146] am335x-phy-driver 47401300.usb-phy: Linked as a consumer to regulator.0 [ 1.704337] musb-hdrc musb-hdrc.0: MUSB HDRC host driver [ 1.709734] musb-hdrc musb-hdrc.0: new USB bus registered, assigned bus number 1 [ 1.717525] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19 [ 1.725855] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.733123] usb usb1: Product: MUSB HDRC host driver [ 1.738121] usb usb1: Manufacturer: Linux 4.19.106-bone49 musb-hcd [ 1.744340] usb usb1: SerialNumber: musb-hdrc.0 [ 1.749499] hub 1-0:1.0: USB hub found [ 1.753375] hub 1-0:1.0: 1 port detected [ 1.758800] am335x-phy-driver 47401b00.usb-phy: 47401b00.usb-phy supply vcc not found, using dummy regulator [ 1.768920] am335x-phy-driver 47401b00.usb-phy: Linked as a consumer to regulator.0 [ 1.785041] omap_rtc 44e3e000.rtc: registered as rtc0 [ 1.790974] i2c /dev entries driver [ 1.796465] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 1.803731] softdog: initialized. soft_noboot=0 soft_margin=60 sec soft_panic=0 (nowayout=0) [ 1.813207] /cpus/cpu@0: unsupported enable-method property: ti,am3352 [ 1.819822] CPUidle arm: CPU 0 failed to init idle CPU ops [ 1.826072] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) [ 1.834858] omap_hsmmc 48060000.mmc: Got CD GPIO [ 1.839925] omap_hsmmc 48060000.mmc: Linked as a consumer to regulator.1 [ 1.873490] omap_hsmmc 481d8000.mmc: Linked as a consumer to regulator.1 [ 1.906292] ledtrig-cpu: registered to indicate activity on CPUs [ 1.912960] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 [ 1.919074] omap-aes 53500000.aes: will run requests pump with realtime priority [ 1.926582] mmc0: host does not support reading read-only switch, assuming write-enable [ 1.936154] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 [ 1.942056] mmc0: Problem switching card into high-speed mode! [ 1.948137] mmc0: new SDHC card at address 0001 [ 1.954565] mmcblk0: mmc0:0001 SD16G 3.75 GiB [ 1.962245] hidraw: raw HID events driver (C) Jiri Kosina [ 1.968034] mmcblk0: p1 [ 1.972349] usbcore: registered new interface driver usbhid [ 1.978052] usbhid: USB HID core driver [ 1.982277] remoteproc remoteproc0: wkup_m3 is available [ 1.988831] gnss: GNSS driver registered with major 242 [ 1.995212] NET: Registered protocol family 10 [ 2.002776] Segment Routing with IPv6 [ 2.006736] mip6: Mobile IPv6 [ 2.009810] NET: Registered protocol family 17 [ 2.014582] Key type dns_resolver registered [ 2.018947] mpls_gso: MPLS GSO support [ 2.022961] ThumbEE CPU extension supported. [ 2.027302] Registering SWP/SWPB emulation handler [ 2.032157] omap_voltage_late_init: Voltage driver support not added [ 2.039022] mmc1: switch to bus width 8 failed [ 2.044503] registered taskstats version 1 [ 2.048704] Loading compiled-in X.509 certificates [ 2.053759] zswap: loaded using pool lzo/zbud [ 2.058319] mmc1: new high speed MMC card at address 0001 [ 2.066126] Btrfs loaded, crc32c=crc32c-generic [ 2.071866] mmcblk1: mmc1:0001 004GA0 3.69 GiB [ 2.076575] AppArmor: AppArmor sha1 policy hashing enabled [ 2.082677] mmcblk1boot0: mmc1:0001 004GA0 partition 1 2.00 MiB [ 2.092266] mmcblk1boot1: mmc1:0001 004GA0 partition 2 2.00 MiB [ 2.101357] mmcblk1rpmb: mmc1:0001 004GA0 partition 3 512 KiB, chardev (244:0) [ 2.110182] mmcblk1: p1 [ 2.145431] tps6521x_pwrbutton tps65217-pwrbutton: DMA mask not set [ 2.152354] input: tps65217_pwr_but as /devices/platform/ocp/44e0b000.i2c/i2c-0/0-0024/tps65217-pwrbutton/input/input0 [ 2.163606] tps65217 0-0024: TPS65217 ID 0xe version 1.2 [ 2.169593] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 2.176610] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz [ 2.183258] remoteproc remoteproc0: powering up wkup_m3 [ 2.188621] remoteproc remoteproc0: Booting fw image am335x-pm-firmware.elf, size 217168 [ 2.199104] cpu cpu0: Linked as a consumer to regulator.3 [ 2.204812] remoteproc remoteproc0: remote processor wkup_m3 is now up [ 2.211381] wkup_m3_ipc 44e11324.wkup_m3_ipc: CM3 Firmware Version = 0x193 [ 2.218396] cpu cpu0: Dropping the link to regulator.3 [ 2.223994] cpu cpu0: Linked as a consumer to regulator.3 [ 2.231275] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 2.261262] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 2.269544] VFS: Mounted root (ext4 filesystem) readonly on device 179:1. [ 2.292095] devtmpfs: mounted [ 2.298931] Freeing unused kernel memory: 1024K [ 2.303986] Run /sbin/init as init process [ 3.312682] systemd[1]: System time before build time, advancing clock. [ 3.387724] systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYP) [ 3.409840] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 10 (buster)! [ 3.441410] systemd[1]: Set hostname to . [ 4.803957] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 4.828278] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R��…uests to Wall Directory Watch. [ 4.857078] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 4.881034] systemd[1]: Listening on Journal Audit Socket. [ OK ] Listening on Journal Audit Socket. [ 4.904302] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. [ 4.928265] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password ��…ts to Console Directory Watch. [ 4.952624] systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. [ OK ] Created slice system-getty.slice. [ OK ] Set up automount Arbitrary��…s File System Automount Point. [ OK ] Listening on udev Kernel Socket. [ OK ] Reached target Swap. [ OK ] Created slice User and Session Slice. [ OK ] Reached target Slices. [ OK ] Listening on Journal Socket. Mounting POSIX Message Queue File System... Starting Load Kernel Modules... Mounting Kernel Debug File System... [ OK ] Listening on Journal Socket (/dev/log). Starting Journal Service... [ OK ] Reached target Paths. [ OK ] Reached target Local Encrypted Volumes. [ OK ] Listening on udev Control Socket. Starting udev Coldplug all Devices... Starting Restore / save the current clock... [ OK ] Listening on fsck to fsckd communication Socket. Starting File System Check on Root Device... [ OK ] Mounted POSIX Message Queue File System. [ OK ] Started Load Kernel Modules. [ OK ] Mounted Kernel Debug File System. Mounting FUSE Control File System... Mounting Kernel Configuration File System... Starting Apply Kernel Variables... [ OK ] Started Restore / save the current clock. [ OK ] Mounted FUSE Control File System. [ OK ] Mounted Kernel Configuration File System. [ OK ] Started File System Check Daemon to report status. [ OK ] Started File System Check on Root Device. Starting Remount Root and Kernel File Systems... [ OK ] Started Apply Kernel Variables. [ OK ] Started Journal Service. [ 6.300162] EXT4-fs (mmcblk0p1): re-mounted. Opts: errors=remount-ro [ OK ] Started Remount Root and Kernel File Systems. Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Create System Users... [ 6.684852] systemd-journald[120]: Received request to flush runtime journal from PID 1 [ OK ] Started Load/Save Random Seed. [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting udev Kernel Device Manager... [ OK ] Started udev Coldplug all Devices. Starting Helper to synchronize boot up for ifupdown... [ OK ] Started Create Volatile Files and Directories. Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Entropy daemon using the HAVEGE algorithm. Starting Network Time Synchronization... [ OK ] Started udev Kernel Device Manager. [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Time Synchronized. [ OK ] Reached target System Initialization. [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Basic System. Starting LSB: Start busybox udhcpd at boot time... Starting Login Service... [ OK ] Started Regular background program processing daemon. [ OK ] Started D-Bus System Message Bus. Starting WPA supplicant... Starting Connection service... Starting Avahi mDNS/DNS-SD Stack... Starting LSB: Load kernel ��…d to enable cpufreq scaling... Starting Generic Board Startup... [ OK ] Started Daily rotation of log files. [ OK ] Reached target Timers. Starting System Logging Service... [ OK ] Started System Logging Service. [ OK ] Started LSB: Start busybox udhcpd at boot time. [ OK ] Started WPA supplicant. [ OK ] Started Login Service. [ OK ] Started Avahi mDNS/DNS-SD Stack. [ OK ] Started Connection service. [ 10.652903] net eth0: initializing cpsw version 1.12 (0) [ 10.690351] libphy: PHY 4a101000.mdio:00 not found [ 10.718523] net eth0: phy "4a101000.mdio:00" not found on slave 0, err -19 Starting Hostname Service... [ 10.810203] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 10.890013] net eth1: initializing cpsw version 1.12 (0) [ 10.923908] libphy: PHY 4a101000.mdio:01 not found [ 10.959438] net eth1: phy "4a101000.mdio:01" not found on slave 1, err -19 [ OK ] Started LSB: Load kernel m��…ded to enable cpufreq scaling. [ 11.034727] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready Starting LSB: set CPUFreq kernel parameters... [ OK ] Started LSB: set CPUFreq kernel parameters. [ OK ] Started Hostname Service. [ OK ] Found device /dev/ttyS0. [ OK ] Started Helper to synchronize boot up for ifupdown. Starting Raise network interfaces... [ OK ] Started Raise network interfaces. [ OK ] Reached target Network. Starting Permit User Sessions... Starting A high performanc��… and a reverse proxy server... Starting OpenBSD Secure Shell server... [ OK ] Started Permit User Sessions. [ OK ] Started Serial Getty on ttyS0. [ OK ] Started Getty on tty1. [ OK ] Started OpenBSD Secure Shell server. [ OK ] Started A high performance��…er and a reverse proxy server. Debian GNU/Linux 10 arm ttyS0 default username:password is [debian:temppwd] arm login: