OTICE: CPU: STM32MP157CAC Rev.Z NOTICE: Model: STMicroelectronics STM32MP157C-DK2 Discovery Board INFO: Reset reason (0x15): INFO: Power-on Reset (rst_por) INFO: PMIC version = 0x21 INFO: FCONF: Reading TB_FW firmware configuration file from: 0x2ffe3000 INFO: FCONF: Reading firmware configuration information for: stm32mp_io INFO: Using SDMMC INFO: Instance 1 INFO: Boot used partition fsbl1 NOTICE: BL2: v2.4-r1.0(debug):devtool-patched NOTICE: BL2: Built : 14:03:27, Mar 8 2022 INFO: BL2: Doing platform setup INFO: RAM: DDR3-DDR3L 16bits 533000Khz WARNING: Couldn't find property st,phy-cal in dtb INFO: Memory size = 0x20000000 (512 MB) INFO: BL2: Loading image id 31 INFO: Loading image id=31 at address 0x2ffff000 INFO: Image id=31 loaded: 0x2ffff000 - 0x2ffff226 INFO: FCONF: Reading FW_CONFIG firmware configuration file from: 0x2ffff000 INFO: FCONF: Reading firmware configuration information for: dyn_cfg INFO: FCONF: Reading firmware configuration information for: stm32mp1_firewall INFO: BL2: Loading image id 4 INFO: Loading image id=4 at address 0x2ffc5000 INFO: Image id=4 loaded: 0x2ffc5000 - 0x2ffd847c WARNING: Not a known TEE, use default loading options. INFO: BL2: Skip loading image id 21 INFO: BL2: Skip loading image id 22 INFO: BL2: Loading image id 23 INFO: Loading image id=23 at address 0xc0500000 INFO: Image id=23 loaded: 0xc0500000 - 0xc0515be8 INFO: BL2: Loading image id 26 INFO: Loading image id=26 at address 0x2ffc0000 INFO: Image id=26 loaded: 0x2ffc0000 - 0x2ffc47dc INFO: BL2: Loading image id 5 INFO: Loading image id=5 at address 0xc0100000 INFO: Image id=5 loaded: 0xc0100000 - 0xc01d3c48 NOTICE: BL2: Booting BL32 INFO: Entry point address = 0x2ffc5000 INFO: SPSR = 0x1d3 NOTICE: SP_MIN: v2.4-r1.0(debug):devtool-patched NOTICE: SP_MIN: Built : 14:03:27, Mar 8 2022 INFO: ARM GICv2 driver initialized INFO: Set calibration timer to 60 sec INFO: stm32mp1 IWDG1 is secure INFO: ETZPC: I2C4 (5) could be non secure INFO: SP_MIN: Initializing runtime services INFO: SP_MIN: Preparing exit to normal world U-Boot 2020.10-stm32mp-r1 (Mar 08 2022 - 14:03:27 +0000) CPU: STM32MP157CAC Rev.Z Model: Seeed Studio Odyssey-STM32MP157C Board Board: stm32mp1 in trusted mode (seeed,odyssey-stm32mp157c) DRAM: 512 MiB Clocks: - MPU : 650 MHz - MCU : 208.878 MHz - AXI : 266.500 MHz - PER : 24 MHz - DDR : 533 MHz WDT: Started with servicing (32s timeout) NAND: 0 MiB MMC: STM32 SD/MMC: 0, STM32 SD/MMC: 1 Loading Environment from MMC... *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial invalid MAC address in OTP 00:00:00:00:00:00 Net: Warning: ethernet@5800a000 (eth0) using random MAC address - 3e:30:58:a0:e3:6f eth0: ethernet@5800a000 Hit any key to stop autoboot: 0 Boot over mmc0! switch to partitions #0, OK mmc0 is current device Scanning mmc 0:4... switch to partitions #0, OK mmc0 is current device npi-booting .... ** Unrecognized filesystem type ** Checking for: /uEnv.txt ... ** Unrecognized filesystem type ** Checking for: /boot.scr ... ** Unrecognized filesystem type ** Checking for: /boot/boot.scr ... ** Unrecognized filesystem type ** Checking for: /boot/uEnv.txt ... ** Unrecognized filesystem type ** ** Unrecognized filesystem type ** ** Unrecognized filesystem type ** ** Unrecognized filesystem type ** ** Unrecognized filesystem type ** ** Unrecognized filesystem type ** after find uEnv.txt bootpart=0:4 mmcdev=0 mmcpart=4 53 bytes read in 32 ms (1000 Bytes/s) Loaded environment from /uEnv.txt debug: [dtb=stm32mp157c-odyssey.dtb] ... Using: dtb=stm32mp157c-odyssey.dtb ... Checking if uname_r is set in /uEnv.txt... Running uname_boot ... npi-uname-booting ....bootpart=0:4 can find /zImage loading /zImage ... 7462784 bytes read in 529 ms (13.5 MiB/s) debug: [enable_uboot_overlays=] ... loading /dtbs/5.10.10-stm32-r1/stm32mp157c-odyssey.dtb ... 62759 bytes read in 37 ms (1.6 MiB/s) uboot_overlays: add [enable_uboot_overlays=1] to /boot/uEnv.txt to enable... debug: [console=ttySTM0,115200 root=/dev/mmcblk0p5 ro rootfstype=ext4 rootwait] ... debug: [bootz 0xC2000000 - 0xC4000000] ... Kernel image @ 0xc2000000 [ 0x000000 - 0x71df80 ] ## Flattened Device Tree blob at c4000000 Booting using the fdt blob at 0xc4000000 Loading Device Tree to cffed000, end cffff526 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.10 (oe-user@oe-host) (arm-ostl-linux-gnueabi-gcc (GCC) 9.3.0, GNU ld (GNU Binutils) 2.34.0.20200220) #1 SMP PREEMPT Tue Mar 8 14:03:28 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Seeed Studio Odyssey-STM32MP157C Board [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Reserved memory: created DMA memory pool at 0x10000000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node mcuram2@10000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x10040000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node vdev0vring0@10040000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x10041000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node vdev0vring1@10041000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x10042000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node vdev0buffer@10042000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x30000000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node mcuram@30000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x38000000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node retram@38000000, compatible id shared-dma-pool [ 0.000000] cma: Reserved 128 MiB at 0xd8000000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000c0000000-0x00000000dfffffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000c0000000-0x00000000d3ffffff] [ 0.000000] node 0: [mem 0x00000000d8000000-0x00000000dfffffff] [ 0.000000] Initmem setup node 0 [mem 0x00000000c0000000-0x00000000dfffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 20 pages/cpu s51788 r8192 d21940 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 113536 [ 0.000000] Kernel command line: console=ttySTM0,115200 root=/dev/mmcblk0p5 ro rootfstype=ext4 rootwait [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 304692K/458752K available (11264K kernel code, 1206K rwdata, 3312K rodata, 1024K init, 247K bss, 22988K reserved, 131072K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] random: get_random_bytes called from start_kernel+0x390/0x568 with crng_init=0 [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000009] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000030] Switching to timer-based delay loop, resolution 41ns [ 0.001300] Console: colour dummy device 80x30 [ 0.001357] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.001386] pid_max: default: 32768 minimum: 301 [ 0.001650] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.001675] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.003027] CPU: Testing write buffer coherency: ok [ 0.003474] /cpus/cpu@0 missing clock-frequency property [ 0.003520] /cpus/cpu@1 missing clock-frequency property [ 0.003541] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.004820] Setting up static identity map for 0xc0100000 - 0xc0100060 [ 0.005024] rcu: Hierarchical SRCU implementation. [ 0.006464] smp: Bringing up secondary CPUs ... [ 0.007684] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.007937] smp: Brought up 1 node, 2 CPUs [ 0.007970] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.007983] CPU: All CPU(s) started in SVC mode. [ 0.008833] devtmpfs: initialized [ 0.033686] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.034066] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.034104] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.040282] pinctrl core: initialized pinctrl subsystem [ 0.042260] NET: Registered protocol family 16 [ 0.045683] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.047560] thermal_sys: Registered thermal governor 'step_wise' [ 0.047962] cpuidle: using governor menu [ 0.048417] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.048440] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.048908] Serial: AMBA PL011 UART driver [ 0.088158] stm32-pm-domain pm_domain: domain core-ret-power-domain registered [ 0.088210] stm32-pm-domain pm_domain: subdomain core-power-domain registered [ 0.088228] stm32-pm-domain pm_domain: domains probed [ 0.115967] SCSI subsystem initialized [ 0.116861] usbcore: registered new interface driver usbfs [ 0.116954] usbcore: registered new interface driver hub [ 0.117033] usbcore: registered new device driver usb [ 0.117349] pps_core: LinuxPPS API ver. 1 registered [ 0.117368] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.117406] PTP clock support registered [ 0.118301] arm-scmi firmware:scmi0: SCMI Notifications - Core Enabled. [ 0.118393] arm-scmi firmware:scmi0: SCMI Protocol v2.0 'ST:' Firmware version 0x0 [ 0.121985] clocksource: Switched to clocksource arch_sys_counter [ 1.566677] NET: Registered protocol family 2 [ 1.567971] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 1.568140] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 1.568216] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 1.568316] TCP: Hash tables configured (established 4096 bind 4096) [ 1.568486] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 1.568541] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 1.569048] NET: Registered protocol family 1 [ 1.570076] RPC: Registered named UNIX socket transport module. [ 1.570104] RPC: Registered udp transport module. [ 1.570117] RPC: Registered tcp transport module. [ 1.570130] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.571312] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available [ 1.573456] Initialise system trusted keyrings [ 1.573854] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 1.584974] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.586450] NFS: Registering the id_resolver key type [ 1.586528] Key type id_resolver registered [ 1.586544] Key type id_legacy registered [ 1.586741] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.586952] ntfs: driver 2.1.32 [Flags: R/O]. [ 1.587285] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 1.588250] fuse: init (API version 7.32) [ 1.589360] NET: Registered protocol family 38 [ 1.589389] Key type asymmetric registered [ 1.589405] Asymmetric key parser 'x509' registered [ 1.589489] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 1.589507] io scheduler mq-deadline registered [ 1.589521] io scheduler kyber registered [ 1.596948] reg11: supplied by regulator-dummy [ 1.597401] reg18: supplied by regulator-dummy [ 1.597768] usb33: supplied by regulator-dummy [ 1.602435] STM32 USART driver initialized [ 1.605249] [drm:dw_mipi_dsi_stm_probe] *ERROR* Unable to get peripheral clock: -517 [ 1.626019] random: fast init done [ 1.626788] brd: module loaded [ 1.630719] random: crng init done [ 1.641107] loop: module loaded [ 1.647227] libphy: Fixed MDIO Bus: probed [ 1.649396] CAN device driver interface [ 1.651309] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 1.651409] usbcore: registered new interface driver pegasus [ 1.651495] usbcore: registered new interface driver asix [ 1.651561] usbcore: registered new interface driver ax88179_178a [ 1.651656] usbcore: registered new interface driver cdc_ether [ 1.651744] usbcore: registered new interface driver smsc75xx [ 1.651830] usbcore: registered new interface driver smsc95xx [ 1.651895] usbcore: registered new interface driver net1080 [ 1.652094] usbcore: registered new interface driver cdc_subset [ 1.652175] usbcore: registered new interface driver zaurus [ 1.652288] usbcore: registered new interface driver cdc_ncm [ 1.653441] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.653500] ehci-platform: EHCI generic platform driver [ 1.653981] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.654028] ohci-platform: OHCI generic platform driver [ 1.654888] usbcore: registered new interface driver usb-storage [ 1.658896] i2c /dev entries driver [ 1.663318] stm32-cpufreq stm32-cpufreq: Failed to get chip info: -517 [ 1.664443] sdhci: Secure Digital Host Controller Interface driver [ 1.664463] sdhci: Copyright(c) Pierre Ossman [ 1.664476] Synopsys Designware Multimedia Card Interface Driver [ 1.664922] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.666189] ledtrig-cpu: registered to indicate activity on CPUs [ 1.666317] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping .... [ 1.666776] usbcore: registered new interface driver usbhid [ 1.666794] usbhid: USB HID core driver [ 1.668220] remoteproc remoteproc0: releasing m4 [ 1.670490] NET: Registered protocol family 17 [ 1.670538] can: controller area network core [ 1.670676] NET: Registered protocol family 29 [ 1.670698] can: raw protocol [ 1.670713] can: broadcast manager protocol [ 1.670735] can: netlink gateway - max_hops=1 [ 1.671567] Key type dns_resolver registered [ 1.671793] ThumbEE CPU extension supported. [ 1.671826] Registering SWP/SWPB emulation handler [ 1.672318] registered taskstats version 1 [ 1.672351] Loading compiled-in X.509 certificates [ 1.715908] stm32-mdma 58000000.dma-controller: STM32 MDMA driver registered [ 1.718450] stm32-dma 48000000.dma-controller: no dma pool: can't use MDMA: 0 [ 1.720110] stm32-dma 48000000.dma-controller: STM32 DMA driver registered [ 1.720765] stm32-dma 48001000.dma-controller: no dma pool: can't use MDMA: 0 [ 1.722559] stm32-dma 48001000.dma-controller: STM32 DMA driver registered [ 1.725026] rpi_touchscreen_dsi_probe be called [ 1.728536] [drm] Initialized stm 1.0.0 20170330 for 5a001000.display-controller on minor 0 [ 1.741194] remoteproc remoteproc0: releasing m4 [ 1.742297] /soc/interrupt-controller@5000d000: bank0 [ 1.742329] /soc/interrupt-controller@5000d000: bank1 [ 1.742351] /soc/interrupt-controller@5000d000: bank2 [ 1.744530] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOA bank added [ 1.744988] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOB bank added [ 1.745398] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOC bank added [ 1.745805] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOD bank added [ 1.746195] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOE bank added [ 1.746611] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOF bank added [ 1.746990] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOG bank added [ 1.747425] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOH bank added [ 1.747814] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOI bank added [ 1.748050] stm32mp157-pinctrl soc:pin-controller@50002000: Pinctrl STM32 initialized [ 1.749330] stm32mp157-pinctrl soc:pin-controller-z@54004000: GPIOZ bank added [ 1.749367] stm32mp157-pinctrl soc:pin-controller-z@54004000: Pinctrl STM32 initialized [ 1.753544] 40010000.serial: ttySTM0 at MMIO 0x40010000 (irq = 56, base_baud = 4000000) is a stm32-usart [ 2.914789] printk: console [ttySTM0] enabled [ 2.922083] stm32-dwmac 5800a000.ethernet: IRQ eth_lpi not found [ 2.926851] stm32-dwmac 5800a000.ethernet: PTP uses main clock [ 2.932513] stm32-dwmac 5800a000.ethernet: no reset control found [ 2.939265] stm32-dwmac 5800a000.ethernet: User ID: 0x40, Synopsys ID: 0x42 [ 2.945532] stm32-dwmac 5800a000.ethernet: DWMAC4/5 [ 2.950407] stm32-dwmac 5800a000.ethernet: DMA HW capability register supported [ 2.957733] stm32-dwmac 5800a000.ethernet: RX Checksum Offload Engine supported [ 2.965010] stm32-dwmac 5800a000.ethernet: TX Checksum insertion supported [ 2.971834] stm32-dwmac 5800a000.ethernet: Wake-Up On Lan supported [ 2.978242] stm32-dwmac 5800a000.ethernet: TSO supported [ 2.983431] stm32-dwmac 5800a000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 2.991197] stm32-dwmac 5800a000.ethernet: device MAC address e2:9c:b5:f8:23:84 [ 2.998506] stm32-dwmac 5800a000.ethernet: Enabled Flow TC (entries=2) [ 3.005006] stm32-dwmac 5800a000.ethernet: TSO feature enabled [ 3.010796] stm32-dwmac 5800a000.ethernet: Using 32 bits DMA width [ 3.020925] libphy: stmmac: probed [ 3.033401] stm32_rtc 5c004000.rtc: registered as rtc0 [ 3.037140] stm32_rtc 5c004000.rtc: setting system clock to 2000-01-01T00:00:08 UTC (946684808) [ 3.046266] stm32_rtc 5c004000.rtc: Date/Time must be initialized [ 3.051831] stm32_rtc 5c004000.rtc: registered rev:1.2 [ 3.079143] rpi_touchscreen_probe be called... [ 3.082398] rpi_touchscreen 2-0045: Atmel I2C read failed: -5 [ 3.088168] stm32f7-i2c 40012000.i2c: STM32F7 I2C-2 bus adapter [ 3.117412] stpmic1 3-0033: PMIC Chip Version: 0x21 [ 3.131094] vddcore: supplied by vin [ 3.136975] vdd_ddr: supplied by vin [ 3.142631] vdd: supplied by vin [ 3.148373] v3v3: supplied by vin [ 3.153382] v1v8_audio: supplied by v3v3 [ 3.161693] v3v3_hdmi: supplied by vin [ 3.168826] vtt_ddr: supplied by vdd_ddr [ 3.172193] vdd_usb: supplied by vin [ 3.178915] vdda: supplied by vin [ 3.184791] v1v2_hdmi: supplied by v3v3 [ 3.191208] vref_ddr: supplied by vin [ 3.194320] bst_out: supplied by vin [ 3.198246] vbus_otg: supplied by bst_out [ 3.202520] vbus_sw: supplied by bst_out [ 3.209878] input: pmic_onkey as /devices/platform/soc/40013000.i2c/i2c-3/3-0033/40013000.i2c:stpmic@33:onkey/input/input0 [ 3.220664] stm32f7-i2c 40013000.i2c: STM32F7 I2C-3 bus adapter [ 3.227013] mmci-pl18x 58005000.sdmmc: Got CD GPIO [ 3.231352] mmci-pl18x 58005000.sdmmc: mmc0: PL180 manf 53 rev2 at 0x58005000 irq 49,0 (pio) [ 3.268769] mmci-pl18x 58007000.sdmmc: mmc1: PL180 manf 53 rev2 at 0x58007000 irq 50,0 (pio) [ 3.307815] stm32-ipcc 4c001000.mailbox: ipcc rev:1.0 enabled, 6 chans, proc 0 [ 3.316550] stm32-rproc 10000000.m4: wdg irq registered [ 3.324976] mmc0: new high speed SDXC card at address aaaa [ 3.330144] remoteproc remoteproc0: m4 is available [ 3.336285] stm32-usbphyc 5a006000.usbphyc: registered rev:1.0 [ 3.341574] mmcblk0: mmc0:aaaa SR128 119 GiB [ 3.346807] dwc2 49000000.usb-otg: supply vusb_d not found, using dummy regulator [ 3.355451] dwc2 49000000.usb-otg: supply vusb_a not found, using dummy regulator [ 3.377988] mmcblk0: p1 p2 p3 p4 p5 [ 3.403907] mmc1: new DDR MMC card at address 0001 [ 3.408570] mmcblk1: mmc1:0001 M62704 3.56 GiB [ 3.412579] mmcblk1boot0: mmc1:0001 M62704 partition 1 2.00 MiB [ 3.418304] mmcblk1boot1: mmc1:0001 M62704 partition 2 2.00 MiB [ 3.424127] mmcblk1rpmb: mmc1:0001 M62704 partition 3 512 KiB, chardev (243:0) [ 3.442776] mmcblk1: p1 p2 p3 p4 p5 p6 [ 3.502431] dwc2 49000000.usb-otg: EPs: 9, dedicated fifos, 952 entries in SPRAM [ 3.509211] dwc2 49000000.usb-otg: DWC OTG Controller [ 3.513567] dwc2 49000000.usb-otg: new USB bus registered, assigned bus number 1 [ 3.520835] dwc2 49000000.usb-otg: irq 80, io mem 0x49000000 [ 3.527945] hub 1-0:1.0: USB hub found [ 3.530326] hub 1-0:1.0: 1 port detected [ 3.536929] ehci-platform 5800d000.usbh-ehci: EHCI Host Controller [ 3.541681] ehci-platform 5800d000.usbh-ehci: new USB bus registered, assigned bus number 2 [ 3.550590] ehci-platform 5800d000.usbh-ehci: irq 59, io mem 0x5800d000 [ 3.582012] ehci-platform 5800d000.usbh-ehci: USB 2.0 started, EHCI 1.00 [ 3.588662] hub 2-0:1.0: USB hub found [ 3.591045] hub 2-0:1.0: 2 ports detected [ 3.597195] ohci-platform 5800c000.usbh-ohci: Generic Platform OHCI controller [ 3.603074] ohci-platform 5800c000.usbh-ohci: new USB bus registered, assigned bus number 3 [ 3.611765] ohci-platform 5800c000.usbh-ohci: irq 52, io mem 0x5800c000 [ 3.687387] hub 3-0:1.0: USB hub found [ 3.689744] hub 3-0:1.0: 2 ports detected [ 3.753542] EXT4-fs (mmcblk0p5): mounted filesystem with ordered data mode. Opts: (null) [ 3.760287] VFS: Mounted root (ext4 filesystem) readonly on device 179:5. [ 3.769324] devtmpfs: mounted [ 3.773119] Freeing unused kernel memory: 1024K [ 3.782425] Run /sbin/init as init process [ 4.226547] systemd[1]: System time before build time, advancing clock. [ 4.390011] NET: Registered protocol family 10 [ 4.433824] Segment Routing with IPv6 [ 4.488472] systemd[1]: systemd 244.5+ running in system mode. (+PAM -AUDIT -SELINUX +IMA -APPARMOR -SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS -ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN2 -IDN -PCRE2 default-hierarchy=hybrid) [ 4.509805] systemd[1]: Detected architecture arm. Welcome to ST OpenSTLinux - Weston - (A Yocto Project Based Distro) 3.1-snapshot-20220307 (dunfell)! [ 4.623478] systemd[1]: Set hostname to . [ 4.650286] systemd[1]: Initializing machine ID from random generator. [ 4.655787] systemd[1]: Installed transient /etc/machine-id file. [ 4.664535] systemd[1]: Hardware watchdog 'STM32 Independent Watchdog', version 0 [ 4.671672] systemd[1]: Set hardware watchdog to 32s. [ 6.962752] systemd[1]: Unnecessary job for /dev/ttySTM0 was removed. [ 6.976858] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. [ 7.014661] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 7.044378] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 7.072852] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. [ 7.102782] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. [ 7.132707] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. [ 7.162386] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 7.192393] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. [ 7.222383] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 7.295285] systemd[1]: Listening on RPCbind Server Activation Socket. [ OK ] Listening on RPCbind Server Activation Socket. [ 7.332533] systemd[1]: Reached target RPC Port Mapper. [ OK ] Reached target RPC Port Mapper. [ 7.363598] systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. [ 7.406425] systemd[1]: Listening on Process Core Dump Socket. [ OK ] Listening on Process Core Dump Socket. [ 7.442913] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. [ 7.479330] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. [ 7.487243] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 7.523443] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 7.553797] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. [ 7.583446] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 7.613129] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 7.643561] systemd[1]: Condition check resulted in Huge Pages File System being skipped. [ 7.657836] systemd[1]: Mounting POSIX Message Queue File System... Mounting POSIX Message Queue File System... [ 7.699690] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... [ 7.751238] systemd[1]: Mounting Temporary Directory (/tmp)... Mounting Temporary Directory (/tmp)... [ 7.790514] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... [ 7.829418] systemd[1]: Starting Mount partitions... Starting Mount partitions... [ 7.876910] systemd[1]: Started Hardware RNG Entropy Gatherer Daemon. [ OK ] Started Hardware RNG Entropy Gatherer Daemon. [ 7.920448] systemd[1]: Starting RPC Bind... Starting RPC Bind... [ 7.970007] systemd[1]: Starting File System Check on Root Device... Starting File System Check on Root Device... [ 8.051854] systemd[1]: Starting Journal Service... Starting Journal Service... [ 8.097590] systemd[1]: Condition check resulted in Load Kernel Modules being skipped. [ 8.146403] systemd[1]: Mounting FUSE Control File System... Mounting FUSE Control File System... [ 8.187423] systemd[1]: Mounting Kernel Configuration File System... Mounting Kernel Configuration File System... [ 8.206820] systemd[1]: Starting Apply Kernel Variables... Starting Apply Kernel Variables... [ 8.229465] systemd[1]: Starting udev Coldplug all Devices... Starting udev Coldplug all Devices... [ 8.304568] systemd[1]: Started RPC Bind. [ OK ] Started RPC Bind. 4] systemd[1]: Mounted POSIX Message Queue File System. [ OK ] Mounted POSIX Message Queue File System. 116] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. .404574] systemd[1]: Mounted Temporary Directory (/tmp). [ 8.421466] EXT4-fs (mmcblk0p4): mounted filesystem with ordered data mode. Opts: (null) [ 8.431582] ext4 filesystem being mounted at /boot supports timestamps until 2038 (0x7fffffff) [ OK ] Mounted Temporary Directory (/tmp). [ 8.449087] systemd[1]: Started Create list of static device nodes for the current kernel. [ OK ] Started Create list of sta… nodes for the current kernel. [ 8.597935] systemd[1]: Mounted FUSE Control File System. [ OK ] Mounted FUSE Control File System. 116] systemd[1]: Mounted Kernel Configuration File System. [ OK ] Mounted Kernel Configuration File System. [ 8.712183] systemd[1]: Started Apply Kernel Variables. [ OK ] Started Apply Kernel Variables. [ 8.832138] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Started Mount partitions. Starting Resize root files…to fit available disk space... [ OK ] Started udev Coldplug all Devices. [ OK ] Started File System Check on Root Device. Starting Remount Root and Kernel File Systems... [ 18.303607] EXT4-fs (mmcblk0p5): re-mounted. Opts: (null) [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started Starts Psplash Boot screen. Starting Flush Journal to Persistent Storage...375] [rpi_touchscreen_get_modes] be call Starting Create System Users... [ 18.481122] systemd-journald[578]: Received client request to flush runtime journal. [ 18.502153] rpi_touchscreen_enable be called [ 18.507355] rpi-ts-dsi 5a000000.dsi.0: I2C write failed: -6 [ OK ] Started Flush Journal to Persistent Storage. [ 18.542347] [rpi_touchscreen_enable] To configure ts->dsi [ OK ] Started Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ 18.862292] rpi-ts-dsi 5a000000.dsi.0: I2C write failed: -6 [ 18.872124] rpi-ts-dsi 5a000000.dsi.0: I2C write failed: -6 Mounting /var/volatile... Starting udev Kernel Device Manager... [ OK ] Mounted /var/volatile. Starting Load/Save Random Seed... [ OK ] Started Load/Save Random Seed. [ OK ] Started udev Kernel Device Manager. [ OK ] Reached target Hardware activated USB gadget. [ 20.680832] galcore: loading out-of-tree module taints kernel. [ 20.889278] Galcore version 6.4.3.279124 [ 22.398405] RESIZE-HELPER START [ 23.094165] RESIZE-HELPER: Using systemd-growfs [ 23.212216] EXT4-fs (mmcblk0p5): resizing filesystem from 31153147 to 31153147 blocks [ 23.299419] EXT4-fs (mmcblk0p4): resizing filesystem from 63355 to 63355 blocks [ 23.433010] Filesystem Size Used Avail Use% Mounted on [ 23.433010] /dev/root 117G 540M 110G 1% / [ 23.433010] devtmpfs 149M 0 149M 0% /dev [ 23.433010] tmpfs 214M 0 214M 0% /dev/shm [ 23.433010] tmpfs 214M 8.6M 205M 4% /run [ 23.433010] tmpfs 214M 0 214M 0% /sys/fs/cgroup [ 23.433010] tmpfs 214M 8.0K 214M 1% /tmp [ 23.433010] /dev/mmcblk0p4 224M 7.5M 199M 4% /boot [ 23.433010] tmpfs 214M 0 214M 0% /var/volatile [ 23.533280] RESIZE-HELPER FINISH [ OK ] Started Resize root filesy…m to fit available disk space. [ OK ] Created slice system-weston.slice. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. [ OK ] Reached target Local File Systems. Starting Rebuild Dynamic Linker Cache... Starting Commit a transient machine-id on disk... Starting Create Volatile Files and Directories... [ OK ] Started Commit a transient machine-id on disk. [ OK ] Started Create Volatile Files and Directories. Starting Run pending postinsts... Starting Rebuild Journal Catalog... Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started Rebuild Journal Catalog. [ OK ] Started Network Time Synchronization. [ OK ] Started Run pending postinsts. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Rebuild Dynamic Linker Cache. Starting Update is Completed... [ OK ] Started Update is Completed. [ OK ] Reached target System Initialization. [ OK ] Started Daily apt download activities. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Listening on dropbear.socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started Kernel Logging Service. [ OK ] Started System Logging Service. [ OK ] Started D-Bus System Message Bus. Starting IPv6 Packet Filtering Framework... Starting IPv4 Packet Filtering Framework... Starting Netdata, Real-time performance monitoring... Starting Login Service... [ OK ] Started TEE Supplicant. Starting Enable USB Ethernet gadget... [ OK ] Started IPv6 Packet Filtering Framework. [ OK ] Started IPv4 Packet Filtering Framework. [ OK ] Reached target Network (Pre). Starting Network Service... [ OK ] Started Netdata, Real-time performance monitoring. [ 28.811486] using random self ethernet address [ 28.815697] using random host ethernet address [ 28.939571] usb0: HOST MAC 68:fb:63:46:94:ea [ 28.942973] usb0: MAC e2:b8:86:ab:18:2b [ 28.946263] dwc2 49000000.usb-otg: bound driver configfs-gadget [ 29.204587] dwc2 49000000.usb-otg: new device is high-speed [ OK ] Started Enable USB Ethernet gadget. [ 29.332818] dwc2 49000000.usb-otg: new device is high-speed [ OK ] Started Network Service. 29.405780] dwc2 49000000.usb-otg: new address 34 [ 29.433687] IPv6: ADDRCONF(NETDEV_CHANGE): usb0: link becomes ready Starting Network Name Resolution... [ 29.580849] stm32-dwmac 5800a000.ethernet eth0: PHY [stmmac-0:03] driver [Micrel KSZ9031 Gigabit PHY] (irq=58) [ OK ] Started Login Service. [ 29.642203] dwmac4: Master AXI performs any burst length [ 29.646492] stm32-dwmac 5800a000.ethernet eth0: No Safety Features support found Starting Userfs cleanup package... [ 29.708318] stm32-dwmac 5800a000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported [ 29.746961] stm32-dwmac 5800a000.ethernet eth0: registered PTP clock [ 29.790785] stm32-dwmac 5800a000.ethernet eth0: configuring for phy/rgmii link mode [ OK ] Started Network Name Resolution. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. Starting Avahi mDNS/DNS-SD Stack... [ OK ] Started IIO Daemon. [ OK ] Started Respond to IPv6 Node Information Queries. Starting Sound Service... [ OK ] Started Network Router Discovery Daemon. Starting Permit User Sessions... Starting Target Communication Framework agent... [ OK ] Started Permit User Sessions. [ OK ] Started Avahi mDNS/DNS-SD Stack. [ OK ] Started Target Communication Framework agent. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttySTM0. [ OK ] Reached target Login Prompts. Starting Weston Wayland Compositor (on tty7)... [ OK ] Started Sound Service. [ OK ] Started Weston Wayland Compositor (on tty7). [ 33.139814] stm32-dwmac 5800a000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 33.153075] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ OK ] Created slice User Slice of UID 0. Starting User Runtime Directory /run/user/0... [ OK ] Started User Runtime Directory /run/user/0. Starting User Manager for UID 0... [ 33.752183] vdda: disabling [ 34.278652] stm32-dwmac 5800a000.ethernet eth0: Link is Down ST OpenSTLinux - Weston - (A Yocto Project Based Distro) 3.1-snapshot stm32mp1 ttySTM0 stm32mp1 login: root (automatic login) Last login: Sun Sep 20 10:44:26 UTC 2020 on tty7 root@stm32mp1:~# [ 41.776126] stm32-dwmac 5800a000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 45.656617] USERFS NOT PRESENT: CLEAN DPKG DATABASE [ 47.929334] stm32-dwmac 5800a000.ethernet eth0: Link is Down [ 55.350347] stm32-dwmac 5800a000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 56.231211] stm32-dwmac 5800a000.ethernet eth0: Link is Down [ 59.754324] stm32-dwmac 5800a000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 61.964319] stm32-dwmac 5800a000.ethernet eth0: Link is Down [ 63.332423] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 63.376186] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 65.254253] stm32-dwmac 5800a000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 71.143064] stm32-dwmac 5800a000.ethernet eth0: Link is Down [ 74.412332] stm32-dwmac 5800a000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 76.707860] stm32-dwmac 5800a000.ethernet eth0: Link is Down [ 84.164542] stm32-dwmac 5800a000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 85.803695] stm32-dwmac 5800a000.ethernet eth0: Link is Down [ 109.477583] stm32-dwmac 5800a000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 110.232269] stm32-dwmac 5800a000.ethernet eth0: Link is Down [ 113.064408] stm32-dwmac 5800a000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 115.777642] stm32-dwmac 5800a000.ethernet eth0: Link is Down [ 118.485608] stm32-dwmac 5800a000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 124.502159] stm32-dwmac 5800a000.ethernet eth0: Link is Down ip a 1: lo: mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: mtu 1500 qdisc mq state DOWN group default qlen 1000 link/ether 56:d0:ac:f2:e5:0b brd ff:ff:ff:ff:ff:ff altname ethernet0 inet6 fe80::54d0:acff:fef2:e50b/64 scope link valid_lft forever preferred_lft forever 3: usb0: mtu 1500 qdisc fq_codel state UP group default qlen 1000 link/ether e2:b8:86:ab:18:2b brd ff:ff:ff:ff:ff:ff inet 192.168.7.1/24 brd 192.168.7.255 scope global usb0 valid_lft forever preferred_lft forever inet6 fe80::e0b8:86ff:feab:182b/64 scope link valid_lft forever preferred_lft forever root@stm32mp1:~# [ 127.821094] stm32-dwmac 5800a000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 128.616068] stm32-dwmac 5800a000.ethernet eth0: Link is Down [ 131.433493] stm32-dwmac 5800a000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 132.192041] stm32-dwmac 5800a000.ethernet eth0: Link is Down [ 134.896853] stm32-dwmac 5800a000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 136.858887] stm32-dwmac 5800a000.ethernet eth0: Link is Down [ 146.808466] stm32-dwmac 5800a000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx ip a 1: lo: mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: mtu 1500 qdisc mq state UP group default qlen 1000 link/ether 56:d0:ac:f2:e5:0b brd ff:ff:ff:ff:ff:ff altname ethernet0 inet 192.168.1.139/24 brd 192.168.1.255 scope global dynamic eth0 valid_lft 86378sec preferred_lft 86378sec inet6 2605:a601:a924:8200:54d0:acff:fef2:e50b/64 scope global dynamic mngtmpaddr noprefixroute valid_lft 3595sec preferred_lft 3595sec inet6 fe80::54d0:acff:fef2:e50b/64 scope link valid_lft forever preferred_lft forever 3: usb0: mtu 1500 qdisc fq_codel state UP group default qlen 1000 link/ether e2:b8:86:ab:18:2b brd ff:ff:ff:ff:ff:ff inet 192.168.7.1/24 brd 192.168.7.255 scope global usb0 valid_lft forever preferred_lft forever inet6 fe80::e0b8:86ff:feab:182b/64 scope link valid_lft forever preferred_lft forever root@stm32mp1:~# root@stm32mp1:~# ================================================================================= $ ssh root@192.168.1.139 root@stm32mp1:~# ls README-CHECK-GPU